混合及混凝攪拌雙曲面攪拌機GSJ-2500-7.5

葉輪材質：玻璃鋼、不銹鋼、

名稱：立式攪拌機、立式曲面攪拌機、曲面攪拌機、雙曲面攪拌機、傘形攪拌機、不銹鋼立式攪拌機、不銹鋼雙曲面攪拌機、玻璃鋼雙曲面攪拌機、雙曲面攪拌機葉輪，GSJ攪拌機，QSJ攪拌機，多曲面攪拌機 自落式攪拌機 立軸式攪拌機 喇叭形攪拌機 污水混合攪拌機

技術參數：

型號：GSJ-2500-7.5

材質：不銹鋼傳動軸

葉輪：玻璃鋼、不銹鋼

功率：7.5KW

葉輪直徑：2500mm

推薦轉速：46r/min,可以根據客戶需求定制轉速。

注意事項  混合及混凝攪拌雙曲面攪拌機GSJ-2500-7.5

混合及混凝攪拌雙曲面攪拌機橋架應校正水平，半橋架立柱應校正垂直。地腳螺栓及連接部位應堅固可靠。    

將減震座平放在橋架規定位置，校正水平后與橋架連接固定。

減速電機安裝在減震座上，并連接固定。

將葉輪與攪拌軸法蘭用螺栓連接并緊固。

將葉輪與攪拌軸放入池內，攪拌軸與減速機輸出軸連接并緊固。

攪拌機安裝后，攪拌軸須與水平面垂直。垂直偏差小于1/1000，且不超過5mm。

混合及混凝攪拌雙曲面攪拌機安裝完畢后，拆下電機尾罩，用手轉動風機葉片，檢查攪拌機轉動是否靈活、正常。攪拌軸擺動偏差應小于3/1000。

接通電源后，點動觀察攪拌軸轉動方向，從上往下看正確轉動方向為逆時針旋轉。若反之.則任意調換2根電源接線位置。

電氣設備安裝必須按凱普德有關規程及安全規程操作。

安裝，使用前請詳細閱讀改產品安裝，使用和維護說明書

在封閉池中藥考慮帶葉輪的zui大尺寸

混合及混凝攪拌雙曲面攪拌機葉輪下緣離池底或其他裝置的垂直距離應保持在150-300mm之間，池內應無任何漂浮物、

注意水下電纜固定牢靠，防止磨損

如果長時間不運行，重啟時時藥防止淤積造成葉輪堵塞而燒毀電機。